Fuel tank selection valves on a catamaran

Giving you more fuel tank options 

One of the great things about catamarans is the redundancy in just about every system.  Fuel tanks are no exception and having a tank for each engine is nice, but it can be made nicer with a transfer pump or better yet, the ability to pick the tank that each engine pulls its diesel from.

But why?

There are couple of reasons that you may want to do this. 

Maybe one engine is not working and you want to be able to go further by using fuel from both tanks for the engine that is working.

If you are getting fuel from an area where this is concern about the quality, you can fill one tank with the suspect fuel, and if it in fact turns out to be bad, you still have the other tank that is known good to fall back on.

We normally run both engines from one tank just so that it is a little bit easier to fill when the time comes.  This is a minor issue on our Vision 444, since the two fuel tanks are just in front of the base of the mast. The filler hose doesn't have to move far to fill one versus the other, but it's still nice to only have to open one tank filler!  By doing this, if we want to run from diesel injector cleaner through the system, we only have to add it to one tank to do so.  

I'm convinced, what's it take?

The gotcha

One thing that must be understood first, is that in a diesel engine, diesel fuel flows in a loop, unlike a gasoline engine. The low pressure pump may deliver 4 liters per hour to the engine, but only a portion of that is used in combustion and the rest must be returned to the tank from which it came.

What exactly happens? (skip if you don't care)

A low pressure, higher volume pump brings fuel into the engine's fuel circuit.  This pump can be either electric, or mechanical (operated by lever on the pump being operated by a fuel cam within the engine). Then a high pressure, low volume pump increases the pressure to be enough to be injected into an already pressurized cylinder or into a pre-cylinder area (indirect injection). Either way, the pressure from this pump can be on the order of 2500psi in an indirect injection engine (like our Nanni engine) or can be as high as 30,000psi in a common rail engine (like the newest Yanmars).  Because of these huge pressures, if too much fuel is delivered, something is going to break.  Diesel injectors have a valve, almost like a blow-off valve in a turbocharger; pressure above a set point escapes and leads to a tube that returns to the fuel tank. The added benefit is that creating all this pressure increases heat; some extra heat is dissipated as the fuel returns to the tank in the return line.

A special valve

So in order to make a fuel selector valve for a diesel engine to work, it must switch two sets of ports when the valve is manipulated.  It's equivalent to a double pole, double throw electrical switch.

Both valves are mounted to the top of our fuel tanks and there is basically a port engine valve and a starboard engine valve.  Changing the valves changes from which tank that engine pulls (and deposits) its fuel.

Here is what the configuration looks like in diagram form:

The Parts

In addition to the valves, there are also some fittings that are required. You may need to adjust the hose barb sizes to fit the fuel lines in your boat, but don't try to get combo right angle barb fittings!!! Mainly because you won't be able to thread them into the valve.  The valves, elbows and barbs have to be assembled in a particular order in order to make it possible.

The following parts assume that the fuel lines are 8mm / 5/16" inside diameter. If yours are not, adjust those fittings accordingly.

Groco 6-Port NPT Bronze Fuel Valve 1/2 Main - 3/8 Return (Order 2)

2 Pack Brass Hose Fitting, Adapter,5/16" Barb x 1/2" NPT Male Pipe (Order 3)

2 Pack Brass Hose Fitting, Adapter, 5/16" Barb x 3/8" NPT Male Pipe (Order 2)

Joywayus Brass Hose Fitting,90 Degree Elbow,5/16" Barb x 3/8" NPT Male Pipe Water/Fuel/Air(Pack of 2)

Litorange 2 PCS Metals Brass Pipe Fitting 90 Degree Barstock Street Elbow 1/2" NPT Male Pipe x 1/2" NPT Female Pipe

Gasoila - SS04 Soft-Set Pipe Thread Sealant with PTFE Paste, Non Hardening, -100 to 600 Degree F, 1/4 Pint Brush

If your fuel tank pickups only have one supply and one return fitting, you will also need the following Y connectors.

Quickun 5/16" ID Hose Brab, Brass Shaped Y 3 Ways Barbed Hose Fitting Intersection Split Splicer Joint Union Adapter for Water/Fuel/Air (Pack of 4)

MarineNow Premium Marine Grade 316 Stainless Steel Hose Clamps 12.7 mm Band, Choose Size and Pack Quantity [SAE:8 (11-23mm,7/16"-15/16"), 25-Pack]

Continental 65127 5/16" ID Fuel Hose - 50 psi - SAE 30R7 - 25' Length

 You will likely not need 25'.  You can also get a high quality fuel hose at a marine or auto store.

1/2-Inch Plastic Pipe Clamp, 2-Hole Mount Strap for 5/8" OD Pipe (10-Pack)- Color may vary

Assembly Order

Because of the closeness of the fittings, you will have to assemble the valves in a specific order.  

Make sure to apply a coating a thread sealant to all male threads before assembly and tighten each connection with two wrenches. Only apply force to the "flats" of the fittings. DO NOT apply force to the barbs; they will break off.

1. Figure out where you are going to mount the valves so you know which way 90 degree fittings should be oriented to make installation easier.
2. Insert the 90 degree 3/8" barb into Port 4 (the smaller, top threaded opening). Tighten until the barb is pointing either towards port 5 or port 6 (whichever works better for your installation)
3. Insert the 1/2" street elbow into Port 3 (the larger, top threaded opening). Tighten until the opening is pointing in the orientation that works for your installation. (Do not point it towards the lever.)
4. You will now have 5 openings remaining (two 3/8" and three 1/2").  Fill these will the appropriate barbs and fully tighten.
5. Repeat steps 1-4 for your other valve.

Installation

Lay out each of the following paths and cut fuel line to make that connection.  Place a hose clamp onto each end of each hose segment.  Do not tighten until everything is connected and you are happy with the layout. This is one plus to ordering extra fuel hose; you can redo any that will make the layout cleaner.

If you only have one fuel supply and one return connection per tank, begin by connecting a length of hose to those connections and placing a "Y" onto the other end of the hose.

Do the following for each valve assembly:

Port 1 will go to the "same side" tank fuel supply pickup.

Notes:
The pickup will be the tube that goes to the bottom of the tank.
If you only have one fuel supply pickup per tank, it will first have to go to the same-side pickup "Y".)

Port 2 will go to the "opposite side" fuel supply pickup

Notes:
The pickup will be the tube that goes to the bottom of the tank.
If you only have one fuel supply pickup per tank, it will first have to go to a opposite-side pickup "Y".)

Port 3 will go to the engine supply line.

Port 4 will go to the engine return line.

Port 5 will go to the "same side" tank fuel return.
Note:
If you only have one fuel return per tank, it will first have to go to a same-side return "Y".)

Port 6 will go to the "opposite side" tank fuel return.
Note:
If you only have one fuel return per tank, it will first have to go to a opposite-side return "Y".)

When you are happy with the layout and hose lengths, secure the hose to surfaces with plastic pipe clamps and tighten all fuel line hose clamps securely.

Labeling, labeling, labeling.

Label the valves so you will quickly know how to set them for the desired operation.

When the handle is facing towards port 1, the fuel is shut off.

When the handle is facing towards port 3 (pointing out), fuel is being pulled from the "same-side" tank.

When the handle is facing towards port 2, fuel is being pulled from the "opposite-side" tank.

Instructions for use

Starboard side valve in Mia

Bleed the system

You will now have to bleed the fuel supply system.  Air will exist in each hose that is proceeding to the valve and from each hose that is supplying fuel to the engine.  All of that air needs to be removed. If you ever run the engines until you run out of fuel, you should make sure that you bleed the system and let the engines idle for 10 or more minutes to make sure that all air has been purged.

Normally, a diesel engine will have a primer lever on it as well as a fuel system bleed screw located near the primary fuel filter.  Make sure you know where there are for your engine.

1. Set both valves to supply fuel from the "same-side" as the engine, ie., port from port, starboard from starboard.
2. If your fuel tanks are below your engines, you may have an electric pump that needs to be powered.
3. Open the bleed screw for the port engine
4. Place a container under your fuel filter to catch the excess fuel; it may be a lot depending on how far the tanks are from your engines.
5. Repeatedly press the Fuel primer level until fuel begins to flow from the bleed screw. Normally, once flowing, it will continue.  Let this continue until you see bubbles pass through and then it runs clear without bubbles.
6. Close the bleed screw.
7. Repeat steps 2-6 for the starboard engine.
   
8. Switch the fuel valves to supply fuel from the "Opposite-side" as the engine, ie., port from starboard, starboard from port.
9. Repeat steps 2-6 for the port engine.
10. Repeat steps 2-6 for the starboard engine.
11. Turn off any electric pump that may have been turned on.
12. The system is now blead.

Test the system

It is a good idea to test the system, as one of two bad things will happen if a connection is wrong. First, your engine will stop, undoubtedly at the worst possible time. Second, you will have swapped the return lines and you will eventually overfill one tank and dump diesel into the water.

Here is one suggestion for testing:

• Disconnect the return hose that goes from each valve and have it go into a small container.
  Run one engine at a time, and make sure that fuel would be returning to the tank you expect.
  Reconnect the hoses.
• To make sure that fuel is being pulled from where you expect, start with tanks that are adequately full, and make a note of the starting fuel gauge level.  Run both engines from one side.  Make sure that only the expected tank level decreases.
• During the first couple of engine uses after installing, make sure that neither tank increases in fuel level.

Moved on to Eleuthera

After a little over a week in The Abacos, we waited for a good weather day to make the trip from Little Harbour to Spanish Wells. Wednesday was the day. The wind was forecasted to swing to northerly, which meant an entrance through the narrow and exposed-to-the-north Ridley Head Channel would not be a great idea. We instead pointed for the further but safer Little Egg Island passage. 

We were still with Umbono, Mira’s sister boat and her owners, Pierre and Kris. 

We left at about 8:00 am with a light breeze from the west. Before long that picked up and we hoisted the main and Code 55 and motor sailed for an hour or so. Then the wind swung as forecast and built more. We put away those sails and raised the asymmetrical spinnaker with 15+ knots almost right behind us. 

The wind continued to build to 18,19, with gusts to 22 knts. The asymmetrical is good to about 20 knots, but since we were downwind running, surfing down waves and generally hauling ass, our apparent wind never went above 15 knts, even at the bottom of waves, so the sail wasn’t being stressed nearly as much as the true wind speed indicated. 

On the trip we were routinely in the 8-9s, sometimes consistently in the low 10s and on one particularly fast surf down a wave, hit 13.1knts! We saw apparent wind speeds of 6! (This is what the wind appears to be because our forward speed is negating some of the true wind speed). 

It ended up being a beautiful sailing day; we even went back to the main (reefed since we would be heading towards the wind after turning, thereby making the apparent wind be faster than the true wind speed) and jib as we entered the protected bay south of Royal Island.

We even caught a nice-sized, male Mahi Mahi on the trip on our rod and reel which we were trolling with. It put up quite a fight on the way in but gave us 8 beautiful fillets. 

Chuck was most excited about our catch!

Kris and Pierre were fighting with some sail issues so motored longer than we did and headed for the Bridge Point entrance, to the Northeast of the town of Spanish Wells. We went the longer route but because we were sailing so fast at that wind angle, we both arrived to Spanish Wells within about 2 minutes of each other (after a trip of about 60NM)!

We even had a pod of 4 dolphins swim by both our boats as we set the anchors. 

There is some great snorkeling around here so hopefully we’ll be able to check a bunch out in the coming days.

We spent Thursday walking around Spanish Wells and checked out some shops and got lunch and a drink at Budda’s Snack Shack. 

Then back to Mira to watch a nice sunset from the roof. 

Quick history lesson: Spanish Wells was so named because it was once a Spanish outpost where early sailing ships would stop before their return from the New World with gold and silver riches. They would stop to get provisions (including filling their water supply) before the long trip to Spain. 

Gulf Stream Crossing - Check!

Synopsys: I would be lying if I said it was smooth sailing.  

Left Thunderbird

We left Thunderbolt, a suburb of Savannah, around 10:00 on the 20th and started the two hour motor down the river to get to the Atlantic. We got a nice send off by dolphins on the way but quickly remembered how far Savannah is inland for such a major port.

Anyways we made it to the Atlantic and the waves had certainly settled down from where they were a few days ago, but that's not really saying much, as we later found out that cruise ships were waiting in Freeport extra days for the weather to calm down!

Waves were pretty short period and around 4-5' close to shore.  They got larger, but at least longer period as we got further offshore. They were hitting us on the beam, maybe a little forward, which does not result in a super pleasant sail. This was proved out because Abe became seasick soon after we entered this weather and went down to his cabin to rest around 1PM on the 20th.  Sue starting feeling less than ideal around 5PM.  

No problem, I'll buckle down and take some longer shifts until they started feeling better. That was a great plan in theory.  In practice, I decided to check on Abe 24 hours later when he hadn't surfaced since. He was awake, but every time he tried to get out of bed, no bueno. Sue was a little better. She was feeling off, but was able to take couple hour shifts at the helm before needing to take a break.  

Single-handing?

Long story short, Abe was basically confined to his bed for almost 72 hours because of how hard this bout of seasickness hit him!  Sue starting doing better on the third day as we made it across the Gulf Stream and things started to calm down.  This is all relative, we were done with the 8-9 foot waves and back to 3-5 footers.

We did manage to sail for almost the entire time and were making good progress if not for the current, which ran at up to 4 knots against us at times.  The expected 48 hour trip turned into 72 hours.  

Land!

We got into Bahamian waters around midnight on the 22nd and still had about 6-7 hours to get to Lucaya, a suburb of Freeport and a friendlier place to clear-in than the very large, commercial port of Freeport.

Navigating close to shore in The Bahamas when dark is generally considered a terrible idea. While there are channels between islands that are a mile deep, as you get close to land, that can quickly drop to 5' or less and there are coral heads. They are not soft. We were happy to be arriving near Lucaya just as the sun was rising, so we wouldn't have to just wait around for daylight. Actually, thinking back and through sheer luck, the timing was pretty much perfect.

The Bahamas

The weather the day we arrived was really nice. We made our way into the relatively narrow channel that goes to Lucaya, then a quirk turn to starboard and the Grand Bahama Yacht Club, where we could check-in to the country, was right there. 

We used their online portal to enter all of our clearing-in information so the visit to the Customs and Immigration office only took about 20 minutes. $300 and we are good to be in The Bahamas for up to 3 months. Of course, as we are on our way back to the boat to shove-off and go the last little bit to the dock-space we rented, the dockhand informed us that they now charge a $50 landing fee.  Of course everything online and in the cruising guidebooks says no charge. After arguing for a few minutes got nowhere, we paid and moved on.  

Scarborough Docks and Villas

We try to anchor whenever possible, however, that's not an option in Lucaya. Fortunately, we stumbled across an entry in AquaMap (BTW, we love this app; if you are a cruiser, you need to use this software!) for what ended up being a fantastic stop for a very fair $75/night, including water, trash and electricity. The owner, Giles, met us at the dock and we were quickly tied up and the trip was done!

Time to Recover

After securing lines and making sure everything was situated, I crashed for a few hours! Abe had a flight the day we arrived and Giles was nice enough to offer to drive him to the airport, so we did make sure we were up to send him off and thank him for travelling with us and then I'm pretty sure we turned in super early to get ourselves back to good.

On our way to The Bahamas!

 After being pinned down in Savannah for quite a while from bad weather, we finally have a good weather window to make the crossing from Thunderbolt, GA (suburb of Savannah) to Freeport, Grand Bahama.  We had a crew member join us yesterday, Abe.  He and his wife found out about a hull slot opening for a Vision 444, came to meet Sue and Mira in Oriental, NC for a tour and to hear about our experience, and decided to jump on the open hull slot!

 Welcome to the Vision Family Abe and Anna!

Abe has been on standby as we have all collectively waited for good weather.  That storm that came up the coast was creating 30-40 knt winds and 12-15 ft waves!  That is finally passed and the weather will be a little bumpy, but we have great reaching winds forecasted the whole way there.  Should make for a fast sail if that forecast proves true.

We expect to arrive in Lucaya (the non-commercial port right next to Freeport) around mid-day on the 22nd.  We'll explore there for a few days and move on, probably to Nassau, where I have to see the US Embassy about getting a new passport. UGH!

I'll add another post soon to cover what we did in Savannah and add one once we arrive in The Bahamas.

Beating to Windward

I forgot to mention in our last post that we are being joined by our friend Jared K. for the trip to Savannah. We’re glad to have him aboard and help with the watch rotation, but we’ll keep him slightly anonymous so that his work doesn’t find out he is working extra-remotely from home…

After the unfortunately eventful trip down Adams Creek to Beaufort, we topped off our diesel tanks and Jerry cans at Town Creek Marina.  Shout out to them! Easy access and the price of diesel was under $4/gallon! The only down side, was that the nozzle was the diameter of my arm, making filling the Jerry cans a nightmare and even the main diesel tanks were no picnic.  

We found a nice spot to anchor in Beaufort (great stop, by the way), visited the local brewery (of course!) and met up with the OCC Port Officer Diane to pick up the couple of items I had sent to her. We didn’t get to stay very long since the weather was looking to get more and more unfavorable as time went on.  

We found (what we thought was) a good time to leave and headed into the Atlantic around 1:00 PM. We knew were going to be close hauled (pointed as close to into the wind as physics allowed our boat to sail) and for the first couple of hours it was unpleasant but tolerable.  For th9sr that haven’t done it, the boat is pushing into the oncoming waves, which are coming from slightly off of one corner of the boat, which pitches the boat up and down, sometimes forcefully. At this point he wins was at about 15 knots and the seas at about 4 feet, though short period, which makes them steep.

Of course that started to build as we got offshore as we pointed to round Frying Pan Shoals, which extends about 20 miles into the Atlantic. The wind was now in the low 20’s, the main was reefed and the waves were building to closer to 6’ (probably!couldn’t see them in the dark). I re-checked the weather and found that a small craft advisory had been issued at about 2:30 and that the wind could be expected to be 30 knots as we got to Frying Pan Shoals,

Not too mention that 2 out of 3 of us were seasick and didn’t take any medicine beforehand, making recovery from medicine now unlikely.  

At this point, Chief Morale Officer Chuck decided we should change plans and head for the nearest, safe inlet.  In this area of NC there is one; Masonboro Inlet, just south of Wrightsville Beach. It would be about 3 hours to get there, but on the plus side, we would be bearing away from the wind, which would increase comfort, but the damage was already done, and seasickness recovery usually doesn’t start until motion stops. 

We eventually got in late (around 2am) and had to enter the channel with pretty large waves rushing in against the outgoing tide.  Hard to know for sure, but some waves seemed to be 6+ feet; thankfully not breaking. We found a nice, close and calm spot to anchor and all quickly turned in to be ready for the next day.